|
|
| Line 1: |
Line 1: |
| '''Please remember, that doing anything instructed here is potentially dangerous. Please see [[General precautions]] for further information.'''
| |
|
| |
|
|
| |
|
| == Modifying led colours and patterns ==
| |
|
| |
|
| There are multiple triggers for led blinking. All can be found in
| | '''THIS PAGE WILL BE REMOVED! THIS WILL BE REDIRECTED TO [[Customizing Maemo]]''' |
| /etc/mce/mce.ini
| |
| | |
| The file can be edited with any text editor that can be run with [[Root access]] and open the file. So GUI - editors probably don't work, but terminal versions all will.
| |
| | |
| === Step by step instructions ===
| |
| | |
| * Open terminal
| |
| * Gain [[Root access]]
| |
| * Make a backup (not necessary!) from original mce.ini -file, for example:
| |
| cp /etc/mce/mce.ini /etc/mce/mce.ini_old
| |
| * Open /etc/mce/mce.ini with a text editor (nano, vim, leafpad...)
| |
| * Search for a line:
| |
| [LEDPatternLystiRX51]
| |
| * Make your changes to the lines below
| |
| * Save
| |
| * Restart mce -process. Either reboot or type to terminal:
| |
| initctl stop mce; sleep 2; initctl start mce
| |
| | |
| === Constructing own patterns ===
| |
| | |
| The mce.ini -file has description header before pattern defining start. Here are the same instructions with longer explanations.
| |
| | |
| Example string:
| |
| PatternCommunicationCall=30;1;0;r;9d80400002ff03ff02ff03ff71080000;9d800000
| |
| | |
| | |
| Dissection:
| |
| {| class="wikitable" border="0"
| |
| |-
| |
| | PatternCommunicationCall=
| |
| | 30;
| |
| | 1;
| |
| | 0;
| |
| | r;
| |
| | 9d80400002ff03ff02ff03ff71080000;
| |
| | 9d800000
| |
| |-
| |
| | Alert pattern
| |
| | priority
| |
| | screen on
| |
| | timeout
| |
| | led mapping
| |
| | Engine 1 pattern
| |
| | Engine 2 pattern
| |
| |}
| |
| | |
| | |
| ==== Priority ====
| |
| This defines that which blinking pattern is the strongest. So if multiple alerts are enabled, which pattern will be shown. Values from 0 to 255 are accepted.
| |
| | |
| ==== Screen on ====
| |
| from mce.ini:
| |
| 0 only show pattern when the display is off
| |
| 1 show pattern even when the display is on
| |
| 2 only show pattern when the display is off, including acting dead
| |
| 3 show pattern even when the display is on, including acting dead
| |
| 4 only show pattern if the display is off, or if in acting dead
| |
| 5 always show pattern, even if LED disabled
| |
| | |
| ==== Timeout ====
| |
| | |
| Time in seconds after blinking is stopped. 0 = infinite blinking.
| |
| | |
| ==== Led mapping ====
| |
| *r/g/b maps led to engine 1,
| |
| *R/G/B maps led to engine 2.
| |
| | |
| examples:
| |
| rGB = red led is mapped to engine 1, green and blue to engine 2
| |
| | |
| rBg = red and green leds are mapped to engine 1, blue to engine 2.
| |
| | |
| You can of course define only one colour, for example:
| |
| r = red led is mapped to engine
| |
| | |
| ==== Engine patterns ====
| |
| | |
| from mce.ini:
| |
| # 0000 -- Jump to the start of the pattern for the channel
| |
| # 40xx -- Set channel brightness
| |
| # 9d80 -- Refresh Mux (use as first command in every pattern!)
| |
| # xxyy -- Increment/decrement
| |
| # xx determines the speed;
| |
| # 02-3f -- short step time (granularity 0.49ms)
| |
| # 42-7f -- long step time (granularity 15.6ms)
| |
| #
| |
| # If xx is even, increment
| |
| # If xx is odd, decrement
| |
| # yy determines the increment/decrement steps
| |
| # 00-ff -- in/decrement steps
| |
| #
| |
| # Use 0 steps to create pauses
| |
| # Two consecutive increment/decrement sequences are needed
| |
| # to cover the entire range from 0-255
| |
| # c000 -- End pattern execution
| |
| # e002 -- Send engine 1 trigger
| |
| # e004 -- Send engine 2 trigger
| |
| # e008 -- Send engine 3 trigger <used by key backlight!>
| |
| # e080 -- Wait for engine 1 trigger
| |
| # e100 -- Wait for engine 2 trigger
| |
| # e200 -- Wait for engine 3 trigger <used by key backlight!>
| |
| | |
| | |
| | |
| source: http://talk.maemo.org/showthread.php?t=37691
| |
|
| |
|
| | led article has moved to [[LED patterns]] |
|
| |
|
| [[Category:Power users]] | | [[Category:Power users]] |
THIS PAGE WILL BE REMOVED! THIS WILL BE REDIRECTED TO Customizing Maemo
led article has moved to LED patterns
Remote WLAN Access To Root / System Files
for easy file manipulation
(please note: all these apps and steps may not be necesarry but I got it working like this)
this help file assumes you know the risks and how to at least download and install apps from the extra repos..
i think you also need
diablo_kernel_usbnet_patch_windows_v0.4
available here:
https://garage.maemo.org/frs/?group_id=801
To get remote access to N900 thru wifi:
1. install the following apps/software
n900 end: (all these apps are in extras repos)
ssh server/client - this will request password when installing (WRITE DOWN / TAKE NOTE OF PASSWORD !!)
rootsh
maemo-pc-connectivity
mad developer
for pc end:
winscp
http://winscp.net/download/winscp425setup.exe
2. goto 'settings' > connectivity > 'pc-connectivity-manager'
3. click "advanced" button > select environment 'default'
4. select connectiont type 'usb'
5. options > select 'network' from drop-down list
6. select connectiont type 'internet' > options > connect using 'WLAN'
7. Save and apply
8. open "mad developer" > manage usb > 'gfile_storage' > close
9. open winscp and put the WLAN ip address shown in mad developer in the 'host name'
10. user name "root", password "(password created during ssh install)"
11. save > login
12. you should now have access!!
